Wheel replacement. Mitsubishi Outlander (since 2003 of release)
Repair and Mitsubishi Outlander service since 2003 of release.
1. Operation and car maintenance
1.1. Car description
1.2. Keys, locks of doors and opening elements of a body
1.3. Governing bodies, kontrolnoizmeritelny devices and salon equipment
1.4. Seats
1.5. System of passive safety
1.6. Sitema of heating and conditioning
1.7. Driving and car service
1.7.1. Recommendations about a car running in
1.7.2. Fuel choice
1.7.3. Trailer towage
1.7.4. Ignition lock
1.7.5. Blocking and unblocking of a steering wheel
1.7.6. Engine start-up
1.7.7. Mechanical transmission
1.7.8. A four-high-speed automatic transmission of INVECS-II Sport Mode (with a manual mode of a choice of transfers – an intellectual and innovative control system of the car of the second generation)
1.7.9. Control lamps of AKPP
1.7.10. Positions of the lever of the selector of an automatic transmission (the main cut)
1.7.11. Features of work of an automatic transmission
1.7.12. Parking brake
1.7.13. Adjustment of height of a steering wheel
1.7.14. Tools and jack
1.7.15. Spare wheel
1.7.16. Wheel replacement
1.7.17. Wheel caps
1.7.18. Towage
1.7.19. Engine overheat
1.7.20. Engine start-up from an external source
1.7.21. Fuses
1.7.22. Replacement of lamps
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Appendix
10. Electric equipment schemes
 







1-7-16-zamena-kolesa.html

1.7.16. Wheel replacement

If replacement of the punctured tire is necessary, do it only after acceptance of all necessary security measures. Put the car in such place where he does not create danger and hindrances for other participants of traffic, this place should be equal.
Observe the traffic regulations existing in the concrete region, concerning safety of the emergency car, i.e. turn on the alarm system, establish at the corresponding distance from the car a sign of an emergency stop ("triangle"), a blinking lamp of the alarm system, etc. All passengers should leave the car.
Establish the car on an equal firm surface and turn on the parking brake. For prevention of moving of the car at a raising its jack establish a brake boot (a persistent block) under a wheel And, located from the opposite side on a diagonal in relation to a replaced wheel of Century.

ATTENTION
Before installation of a jack be convinced that the brake boot or a persistent block are enclosed under a wheel. If the car moves a little during its raising, the jack can jump out from under a body and it can lead to accident.

NOTE
The brake boot shown in drawing, does not enter into a car complete set. It is recommended to get it separately for use if necessary.

If the brake boot is not present, enclose under a wheel a stone or any subject suitable on the size which can hold a wheel on a place.
Get a spare wheel, prepare a jack and a key for nuts of wheels (a ballonny key).

NOTE
Enclose a spare wheel under a car body about a jack. It will reduce danger in case the jack breaks.

On the car with wheel caps weaken nuts of wheels by means of a key for nuts of wheels. Do not remove a nut of wheels at this stage.
By means of a jack lift the car until the lowered tire slightly will not come off the earth.
Turn off nuts of wheels a key for nuts of wheels or a hand, then remove a wheel.
Remove dirt, etc. from a nave surface With, from hairpins of the D nave and from openings under hairpins Е in a disk of a wheel and after that establish a spare wheel on a nave.
If the disk of a wheel is made of steel (type 1), establish wheel nuts a konusny part to a wheel and tighten them by hand so that the wheel had no люфта.
If the disk of a wheel is made of an aluminum alloy (type 2), temporarily tighten nuts by hand before contact of flanges of nuts with a wheel disk so that the last had no люфта.

NOTE
Temporary installation of flange wheel nuts (type 2) on a steel disk is allowed, however at the first possibility it is necessary to establish an original disk and the tire.

If all four wheels on the car with aluminum disks and flange wheel nuts (type 2) change on wheels with steel disks, it is necessary to establish konusny wheel nuts (type 1).

ATTENTION
Never oil hairpins or nuts of fastening of wheels as it can lead to their peretyazhka.

Slowly lower the car, and then serially, for some receptions, tighten all wheel nuts till the specified moment of an inhaling.
Inhaling moment: 98–108 N · m. (The moment is reached by the effort appendix approximately from 360 to 420 N on the end of a ballony key for nuts of wheels which is delivered together with the car.)

ATTENTION
At an inhaling of nuts of fastening of a wheel it is forbidden to rise a foot on a wrench or to extend the last by means of a pipe as it can lead to a nut peretyazhka.

Lower a jack, take out it from under the car. Clean in places of regular storage a jack, a montazhka and a wheel with the lowered tire. Repair it at the first possibility.
Check pressure of air in the tire. Pressure corresponding to technical requirements in the tire is specified on a sticker located on a rack from the driver.


1.7.15. Spare wheel

1.7.17. Wheel caps