Repair and Mitsubishi Outlander service since 2003 of release.
1. Operation and car maintenance
2. Engine
2.1. The general procedures of check and prevention without removal of the power unit
2.2. Removal and engine installation assembled
2.3. System of cooling of the engine
2.3.1. Check of a leakage of system of cooling
2.3.2. Check of pressure of opening of the valve of a stopper of a radiator
2.3.3. Replacement of cooling liquid
2.3.4. Check of the electronic block of the electrofan
2.3.5. Check of the relay of the electrofan
2.3.6. Removal and thermostat installation
2.3.7. Removal and installation of the pump of cooling liquid
2.3.8. Removal and installation of a water hose and water pipe
2.3.9. Removal and installation of a radiator of system of cooling
2.4. Greasing system
2.5. System of the distributed injection of fuel (MPI) of engines of a series 4G6
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Appendix
10. Electric equipment schemes
 





Дизайн эксклюзивная мебель еще по теме.

2-3-3-zamena-okhlazhdayushhejj-zhidkosti.html

2.3.3. Replacement of cooling liquid

NOTE
At removal of a stopper of a radiator be careful not to get burns hot cooling liquid or steam. Wind a radiator stopper with a towel and turn it counter-clockwise for pressure dumping through a parootvodny tube a little. After dumping of pressure remove a stopper, having slowly turned it counter-clockwise.

Replacement of cooling liquid
After removal of a stopper of a radiator unscrew a drain stopper of a radiator and merge cooling liquid from a radiator, a heater and the engine.
Merge liquid from a shirt of cooling of the engine, having unscrewed a drain stopper of the block of cylinders.
Remove a broad tank and merge from it cooling liquid.
After plum of all cooling liquid wash out cooling system, having sent to a jellied branch pipe of a radiator a water stream under pressure.
Replacement of cooling liquid
Grease with hermetic a carving part of a drain stopper of the block of cylinders and tighten it the specified moment.
Hermetic name: ZM nomenclature number 4171 for carving connections or equivalent.
Inhaling moment: 44 + 5 N · m.
Reliably wrap a drain stopper of a radiator.
Establish a broad tank.

ATTENTION
It is forbidden to use alcohol – or metanolsoderzhashchy cooling liquid, and also their mixes with any of glikolevy cooling liquids. Use of the forbidden cooling liquids can cause corrosion of details from aluminum alloys.

Replacement of cooling liquid
Choose concentration of solution of nizkoza-merzayushchy liquid depending on ambient temperature. Concentration of solution should be in a range of 30-60 %. For filling of cooling liquid use a set for an opressovka (МВ991871). The solution containing 50 % of water and 50 % of a concentrate of low-freezing liquid (freezing temperature usually prepares:–31 °C).
Recommended brand of a concentrate of low-freezing liquid: DIAQUEEN SUPER LONG LIFE COOLANT or analog.
Quantity: 7,0 l.

NOTE
Before use of the Mv991871 adaptation familiarize with the maintenance instruction enclosed to this adaptation.

Establish a radiator stopper.
Start the engine and warm up it to temperature of opening of the valve of the thermostat.
Several times increase frequency of rotation to 3000 mines-1 after that muffle the engine.
Let's to the engine cool down.
Remove a stopper of a radiator and add cooling liquid to edge of a jellied mouth.
Establish a radiator stopper.

ATTENTION
Do not allow overflow of a broad tank.

If necessary add cooling liquid in a broad tank so that level of liquid was between marks of "F" and «L».

Determination of concentration of solution of low-freezing liquid
For determination of concentration of solution of cooling liquid it is necessary to take its temperature of freezing and density.
Nominal rate: 30–60 %.
Recommended brand of a concentrate of low-freezing liquid: DIAQUEEN SUPER LONG LIFE COOLANT or equivalent.

ATTENTION
If concentration of solution of low-freezing liquid less than 30 %, anticorrosion properties of such solution are essentially reduced. If concentration is higher than 60 %, a thermal capacity of such solution of less settlement meaning – a niya that worsens engine refrigerating conditions. Therefore it is necessary to watch concentration of solution of cooling liquid strictly.


2.3.2. Check of pressure of opening of the valve of a stopper of a radiator

2.3.4. Check of the electronic block of the electrofan