Liquid replacement in an automatic transmission. Mitsubishi Outlander (since 2003 of release)
Repair and Mitsubishi Outlander service since 2003 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
3.1. The general procedures of check and prevention on the car
3.2. Operations on the heated-up engine
3.2.1. Check of level of liquid in an automatic transmission
3.2.2. Liquid replacement in an automatic transmission
3.2.3. Washing of the hydraulic line of the heat exchanger of a transmission
3.3. Coupling
3.4. Mechanical transmission
3.5. Automatic transmission
3.6. Driveshaft and driving mechanism
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Appendix
10. Electric equipment schemes
 







3-2-2-zamena-zhidkosti-v-avtomaticheskojj-korobke-peredach.html

3.2.2. Liquid replacement in an automatic transmission

Technical characteristics
Liquid for automatic transmissions: DIA QUEEN ATF SP III.
Amount of filled-in liquid: 8,1 l.

Replacement technique
If at your order there is an installation for replacement of working liquid in an automatic transmission, it is recommended to use it for washing of a transmission and liquid replacement. If at your order there is no installation for replacement of working liquid, follow the technique given below.
Disconnect a hose shown in drawing which connects a transmission to the heat exchanger (in a radiator).
Start the engine and let's to working liquid flow down. Position of the selector: at operation of the engine idling the selector is in the situation "N".

ATTENTION
The engine should be muffled in one minute after its start. If liquid flowed out earlier, respectively and the engine should be muffled earlier.

Amount of merged liquid: about 3,5 l.
Unscrew the drain stopper located in the lower part of the case of a transmission on purpose plum of the remains of liquid.
Merged quantity: about 2,0 l.
Wrap a drain stopper, previously having established new laying, and tighten the demanded moment of an inhaling.
The recommended moment of an inhaling: 32 ± 2 N · m.
Fill in through a jellied mouth fresh ATF liquid.
Recommended quantity: about 5,5 l.

ATTENTION
Fill in strictly 5,5 lzhidkost.

Again start the engine and let's to working liquid flow down.
Fill in fresh AFT through a jellied mouth.
Recommended quantity: About 3,5 l.

NOTE
Warm up, merge and fill in liquid until from a tube of cooling, at least, 8,0 l will not merge. After that merge still a small amount of ATF and check on existence of pollution, then repeat operations.

Connect a hose disconnected earlier, insert щуп. Start the engine and let's to it work idling 1–2 minutes. Transfer the selector lever to each situation, returning its each time in neutral situation. Check, whether there is a liquid level on COLD mark (cold). If level of liquid does not reach this mark, add still liquids.
Make a trip on the car so that the temperature of liquid reached working temperature (70–80 °C) and then check liquid level. Level of liquid should be between «HOT» labels (hot).

NOTE
«COLD» mark (cold) serves for the help purposes. «HOT» marks (hot) are used for definition of level of liquid.

Make measurement of temperature of ATF by means of MUT II/III.
If for warming up of a transmission rather long time is necessary, determine level of working liquid by the table providing level of liquid at this temperature to temperature of liquid of 70-80 °C.
If level of working liquid is lower recommended, add it. If level of ATF exceeds recommended level, merge superfluous amount of liquid through a drain opening.
Densely vstavtemaslyany щуп in a maslozalivny tube


3.2.1. Check of level of liquid in an automatic transmission

3.2.3. Washing of the hydraulic line of the heat exchanger of a transmission