Repair and Mitsubishi Outlander service since 2003 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
3.1. The general procedures of check and prevention on the car
3.2. Operations on the heated-up engine
3.3. Coupling
3.4. Mechanical transmission
3.5. Automatic transmission
3.6. Driveshaft and driving mechanism
3.6.1. Removal and driveshaft (4WD) installation
3.6.2. Driveshaft check
3.6.3. Dismantling and driveshaft assembly
3.6.4. Removal and installation of a shaft of a drive of a wheel assembled
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Appendix
10. Electric equipment schemes
 







3-6-4-snyatie-i-ustanovka-vala-privoda-kolesa-v-sbore.html

3.6.4. Removal and installation of a shaft of a drive of a wheel assembled

ATTENTION
During dismantle and installation of a power shaft be careful not to strike a gear wreath of the sensor of speed of rotation of a wheel which is established on an external ring of the external hinge of equal angular speeds. Otherwise the gear wreath of the sensor will be damaged.
During works on maintenance be careful not to strike the polar tip located in the top part of the sensor of speed of rotation of a forward wheel.

Removal
Merge oil from a transmission. (4WD models) Merge oil from a transfer case.
Remove a reception pipe of system of release.

ATTENTION
In order to avoid breakage during an otvorachivaniye of a nut of fastening of a power shaft it is necessary to hang out a wheel to unload the nave bearing.

Dismantle of a nut of fastening of a power shaft
Removal and installation of a shaft of a drive of a wheel assembled
To fix a nave and to unscrew a nut of fastening of a power shaft, use the special holder (МВ990767).

ATTENTION
Do not remove a nut from a finger of the spherical hinge. Only weaken its fastening. Use the special tool not to damage a carving on a finger of the spherical hinge. Adhere a cord a stripper to prevent its falling.

Dismantle сомоконтрящейся nuts (fastening of a tip of steering draft)
Removal and installation of a shaft of a drive of a wheel assembled
Establish a stripper of spherical hinges (МВ991897) as it is shown in drawing.
Removal and installation of a shaft of a drive of a wheel assembled
In case of need turn the handle and a bolt to establish pads in parallel relatively each other. Tighten a bolt by hand, observing parallelism of pads.

ATTENTION
Having established pads in parallel relatively each other, be convinced that the handle occupies the situation shown in drawing.

Tighten a bolt a wrench to disconnect a tip of steering draft.

Dismantle of a power shaft
Removal and installation of a shaft of a drive of a wheel assembled
To remove a power shaft from a nave, use the following special tool.
– Stripper of a power shaft (МВ990241).
– Screw of a stripper (МВ990242).
– Bracket of a stripper (МВ990244).
– Basis of a stripper (МВ991354).
– Holder (МВ990767).
Removal and installation of a shaft of a drive of a wheel assembled
Remove a power shaft from a nave, having undertaken the lower part of a brake disk and having pulled it on itself.

ATTENTION
Do not put efforts to a power shaft. Otherwise you can damage the hinge of equal angular speeds. Use for this purpose mount.
During dismantle of a power shaft from a transmission be careful not to damage an epiploon shlitsa of a power shaft.

Removal and installation of a shaft of a drive of a wheel assembled
Insert a montrovka between a case of a transmission and a power shaft. Use mount as the lever and take out a power shaft from a transmission.
Removal and installation of a shaft of a drive of a wheel assembled
If the detachment of an internal shaft from a transmission is complicated, remove a shaft, slightly tapping with a plastic hammer on an arm of an intermediate support assembled.
Removal and installation of a shaft of a drive of a wheel assembled
Establish a special cap (МВ991460) to prevent penetration of extraneous materials into a transmission case.
In order to avoid breakage during dismantle of a power shaft it is necessary to hang out a wheel to unload the nave bearing. In case of need car movings with a support on wheels temporarily fix the bearing, vospolzvovav-shis the following special tool.
Removal and installation of a shaft of a drive of a wheel assembled
– Rasporny plug (МВ991000).
– The adaptation for dismantle and installation of a nave of a forward wheel (МВ991017).

Removal of an internal power shaft (4WD Model)
Removal and installation of a shaft of a drive of a wheel assembled
By means of the special tool remove a shaft.

ATTENTION
Do not damage an epiploon shlitsa of a shaft of a drive of a wheel at shaft removal.

Installation of a power shaft

ATTENTION
In an installation time of a power shaft be careful not to damage an epiploon shlitsa of a power shaft.

Installation of a pillow and самоконтрящейся nuts (fastening of the stabilizer of cross-section stability)
Establish a pillow and the plug, as is shown in drawing. Tighten самоконтрящуюся a nut so that the length of an acting part (And) a bolt of fastening of a bar of the stabilizer corresponded to demanded value.
Removal and installation of a shaft of a drive of a wheel assembled
Demanded value (And): 9,4 ±0,3 mm.

NOTE
Be вниманительны to observe the correct orientation of a washer and a nut of fastening of a power shaft.

ATTENTION
Before a final inhaling of nuts of fastening of power shafts be convinced that bearings of a nave are not under loading. Otherwise the podshinik will be damaged.

Installation of a washer and nut of fastening of a power shaft
Removal and installation of a shaft of a drive of a wheel assembled
Having used the special holder (МВ990767), tighten a nut of fastening of a power shaft with the moment of the established size.
Size of the moment of an inhaling: 245 ± 29 N · m.


3.6.3. Dismantling and driveshaft assembly

4. Running gear