Removal and installation of the bottom lever of a suspension bracket. Mitsubishi Outlander (since 2003 of release)
Repair and Mitsubishi Outlander service since 2003 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
4.1. The general procedures of check and prevention on the car
4.2. Tires and wheels
4.3. Peredny Bridge
4.4. Forward suspension bracket
4.4.1. General information
4.4.2. Dismantling and assembly of a telescopic rack assembled
4.4.3. Removal and installation of the bottom lever of a suspension bracket
4.5. Back suspension bracket
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Appendix
10. Electric equipment schemes
 







4-4-3-snyatie-i-ustanovka-nizhnego-rychaga-podveski.html

4.4.3. Removal and installation of the bottom lever of a suspension bracket


Check on the car
Check a protective cover of a spherical support on existence of cracks or damages, squeezing fingers a cover.
Check and adjustment of corners of installation of forward wheels.

Otvorachivaniye of a bolt of the bottom lever of a suspension bracket
Raise a transmission a jack, then turn out a forward bolt of the bottom lever of a suspension bracket (cars with the left arrangement of governing bodies).
Installation of a nut of a telescopic rack (самоконтрящейся nuts)
Tighten самоконтрящуюся a nut so that the length of an acting carving part of a bar of the stabilizer of cross-section stability left on nominal size.
Nominal rate (And): 9,4 ± 0,4 mm

Check
Check a condition of plugs of the bottom lever of a suspension bracket on wear or destruction existence.
Check a condition of the bottom lever of a suspension bracket assembled on curvature or destruction existence.
Check a condition of all bolts of fastening (a condition of a carving and curvature).

Check of the moment of the beginning of a provorachivaniye of the spherical hinge of the bottom lever
Several times stir up the spherical hinge, then by means of the special tool (МВ991006) measure the moment of the beginning of a provorachivaniye of the spherical hinge.
Nominal rate: 0–3,9 N · m.
If the measured size of the moment does not correspond to norm, or the spherical hinge turns hardly or with jamming, replace the bottom lever of a suspension bracket assembled.

Check of a protective cover of the spherical hinge of the bottom lever
Check a protective cover of a spherical support on existence of cracks or damages, squeezing fingers a cover.
In the presence of cracks or damages of a protective cover of the spherical hinge, replace the bottom lever assembled.

ATTENTION
Cracks or damage to a protective cover can cause damage of the spherical hinge. At damage of a protective cover during work in a workshop, replacement only the protective cover of a spherical support of the bottom lever of a suspension bracket is subject.

Replacement of a protective cover of the spherical hinge of the bottom lever
At damage of a protective cover during work in a workshop, replace only a protective cover of a spherical support of the bottom lever of a suspension bracket.
Remove a protective cover of the spherical hinge of the bottom lever.
Put recommended plastic greasing on an edge and in inside new protective cover.
Recommended lubricant: Plastic greasing SAE J310, NLGI No. 2 or equivalent to it. Necessary amount of greasing for a protective cover (help value): 8–10 g
By means of the special tool for removal/installation of spherical hinges (МВ990800), put on a protective cover the spherical hinge before its complete fixing in a place.
Protective cover of the spherical hinge of the bottom lever of a suspension bracket of 22 mm.
Establish a protective cover of the spherical hinge of the bottom lever how it is shown in drawing. Be convinced of lack of an abnormal vspuchivaniye or the pressure attached to a protective cover by the spherical hinge of the bottom lever.
Check a protective cover of a spherical support on existence of cracks or damages, squeezing fingers a cover.

Replacement of the back plug of the bottom lever
Replace the back plug of the bottom lever of a suspension bracket, having executed the following operations.
For extraction of the back plug of the bottom lever of a suspension bracket the following special tool is used.
– МВ990883: an opravka for the back plug of a suspension bracket.
– МВ990972: basis of a stripper of the plug of a torsionny shaft.
– МВ990887: ring.
– МВ990890: basis of the plug of a back suspension bracket.
Arrange the back plug of the bottom lever so that its ledge was located, as is shown in drawing, then, by means of the special tool, press the plug.
Press the plug until its external tube does not become aflush with a surface of the bottom lever.


4.4.2. Dismantling and assembly of a telescopic rack assembled

4.5. Back suspension bracket