Repair and Mitsubishi Outlander service since 2003 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
4.1. The general procedures of check and prevention on the car
4.2. Tires and wheels
4.3. Peredny Bridge
4.4. Forward suspension bracket
4.5. Back suspension bracket
4.5.1. General information
4.5.2. Removal and installation of levers of a suspension bracket
4.5.3. Installation of the top lever in the collecting / managing director of a bar of a suspension bracket
4.5.4. Removal and installation of the longitudinal lever assembled
4.5.5. Removal and shock-absorber installation assembled
4.5.6. Dismantling and assembly of an amortizatorny rack
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Appendix
10. Electric equipment schemes
 







4-5-3-ustanovka-verkhnego-rychaga-v-sbore-upravlyayushhejj-shtangi-podveski.html

4.5.3. Installation of the top lever in the collecting / managing director of a bar of a suspension bracket

Installation of the top lever in the collecting / managing director of a bar of a suspension bracket

Installation of the top lever in the collecting / managing director of a bar of a suspension bracket
Establish the top lever in the collecting / managing director a bar as is shown in drawing that color labels were turned to the longitudinal lever.

Check
Check a condition of plugs on wear or destruction existence.
Check a condition of an operating bar, the top and bottom levers of a suspension bracket on existence погнутосни or destructions.
Check a condition of all bolts of fastening (a condition of a carving and curvature).
Check of the moment of the beginning of a provorachivaniye of an operating bar / the top lever of a suspension bracket / the bottom lever of a suspension bracket in the basic bearing
Installation of the top lever in the collecting / managing director of a bar of a suspension bracket
Check a condition of each basic bearing as follows.
Insert an assembly bolt into an opening of the basic bearing. From the opposite side dress a washer and screw an assembly nut.
Installation of the top lever in the collecting / managing director of a bar of a suspension bracket
Several times turn the internal plug of the bearing, then by means of the special tool (МВ990326) measure the moment of the beginning of a provorachivaniye of the plug of the basic bearing.
Nominal rate: 0,5–3,0 N · m.
If the measured size surpasses nominal size, replace the basic bearing of the managing director of a bar, or the top lever of a suspension bracket, or the bottom lever of a suspension bracket.
If the measured size less nominal rate, be convinced that the basic bearing rotates freely, without considerable люфта.
In the absence of considerable люфта and at smooth rotation, the basic bearing can be used repeatedly.

Replacement of the plug and basic bearing of the bottom lever
Installation of the top lever in the collecting / managing director of a bar of a suspension bracket
Replace the plug and the basic bearing of the bottom lever of a suspension bracket, having executed the following operations.

Replacement of the plug of the bottom lever

ATTENTION
As external diameter of the plug on its different ends different, be attentive: do not mix the direction of installation of the plug.

Installation of the top lever in the collecting / managing director of a bar of a suspension bracket
Installation of the top lever in the collecting / managing director of a bar of a suspension bracket
For a press fitting / выпрессовки plugs use the following special tool.
– МВ991447: the adaptation for removal/installation of plugs.
– МВ991448 the basis for removal / installation of plugs.
– МВ991449: a support for removal/installation of plugs.
Upon termination of a plug press fitting, the distance between edges of an external sleeve of the plug and the bottom lever should make 1,5 mm (see drawing).

Replacement of the basic bearing of the bottom lever of a suspension bracket
Installation of the top lever in the collecting / managing director of a bar of a suspension bracket
For a press fitting / vypressovka of the plug use the following special tool.
– МВ990957: The adaptation for removal / installation of the plug of the bottom lever of a suspension bracket.
– МВ990969: Directing.
– МВ990971: Basis.
– МВ990996: Opravka for the plug of the bottom lever of a suspension bracket.
Upon termination of a plug press fitting, the distance between edges of an external sleeve of the plug and the bottom lever should make 3,0 mm (see drawing).


4.5.2. Removal and installation of levers of a suspension bracket

4.5.4. Removal and installation of the longitudinal lever assembled