Dismantling and assembly of an amortizatorny rack. Mitsubishi Outlander (since 2003 of release)
Repair and Mitsubishi Outlander service since 2003 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
4.1. The general procedures of check and prevention on the car
4.2. Tires and wheels
4.3. Peredny Bridge
4.4. Forward suspension bracket
4.5. Back suspension bracket
4.5.1. General information
4.5.2. Removal and installation of levers of a suspension bracket
4.5.3. Installation of the top lever in the collecting / managing director of a bar of a suspension bracket
4.5.4. Removal and installation of the longitudinal lever assembled
4.5.5. Removal and shock-absorber installation assembled
4.5.6. Dismantling and assembly of an amortizatorny rack
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
9. Appendix
10. Electric equipment schemes
 





На http://www.sola.com.ua установка автостекол.

4-5-6-razborka-i-sborka-amortizatornojj-stojjki.html

4.5.6. Dismantling and assembly of an amortizatorny rack

Otvorachivaniye of a nut of a spring of a back suspension bracket (самоконтрящаяся nut)

ATTENTION
Having fixed a suspension bracket spring, establish exactly special tool (МВ991239) so that its maximum length corresponded to length of a spring.

Use of a shock key for a twisting of a bolt of the adaptation for compression of a spring (МВ991237) is not allowed. The special tool will break.
For compression of a spring of a suspension bracket use the following special tool.
– МВ991237: the device for spring compression.
– МВ991239: set of levers.

ATTENTION
Application of a shock key for an otvorachivaniye of a nut of a spring of a back suspension bracket (самоконтрящуюся a nut) not the dopuskayetsy Vibration proceeding from a shock key, causes a soskalzyvaniye of the special tool (МВ991237 and МВ991239) that leads to a trauma.

Holding from a provorachivaniye a piston rod, unscrew a nut of a spring of a back suspension bracket (самоконтрящуюся a nut).

Utilization of the shock-absorber of a back suspension bracket

ATTENTION
Dress goggles for protection of eyes against flying metal shaving.

Before delivery in junk, gas should be removed from a telescopic rack. Lay a telescopic rack horizontally and put forward a rack rod. Drill an opening in diameter about 3 mm in a place shown in drawing and let out gas from a rack.

Installation of the bottom basic cup of a spring of a back suspension bracket
Combine a step part of the bottom pillow with a step part of the bottom basic cup of a spring of the shock-absorber and establish into place the bottom pillow of a spring.

Installation of a spring of a back suspension bracket

ATTENTION
Use of a shock key for a twisting of a bolt of the adaptation for compression of a spring (МВ991237) is not allowed. The special tool will break.

By means of the special tool compress a spring and establish it on the bottom pillow of a spring of a back suspension bracket.
– МВ991237: the device for spring compression.
– МВ991239: set of levers.
The lower part of a spring of a back suspension bracket should be located how is shown in drawing.

Installation of the top basic cup of a spring of a back suspension bracket
Combine a step part of the top pillow with the top part of a spring of the shock-absorber and establish into place the top pillow of a spring.

Installation of the top support of the back shock-absorber
Establish the top support of the back shock-absorber so that the axis of an internal tube of the bottom plug of the shock-absorber was on lines between bolts of fastening of a support at a view of knot directly from above.

Navorachivaniye of a nut of a spring of a back suspension bracket (самоконтрящейся nuts)
Short tighten a nut of a spring of a back suspension bracket (самоконтрящуюся a nut).

ATTENTION
Application of a shock key for a nut wraparound (самоконтрящейся nuts) springs of a back suspension bracket is not allowed, otherwise самоконтрящаяся the nut will be damaged.

Remove the special tool (МВ991237, МВ991239), and finally tighten a nut of a spring of a back suspension bracket (самоконтрящуюся a nut) the moment 25 ±5Н · m.


4.5.5. Removal and shock-absorber installation assembled

5. Steering mechanism