Repair and Mitsubishi Outlander service since 2003 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
5.1. A steering with the hydraulic booster
5.2. The general procedures of check and prevention on the car
5.2.1. Check of a free wheeling and check of an angle of rotation of a steering wheel
5.2.2. Check of the moment of the beginning of a provorachivaniye of the spherical hinge of a tip of steering draft
5.2.3. Check of effort of turn of a steering wheel at the motionless car
5.2.4. Check of self-return of a steering wheel in the provision of rectilinear movement
5.2.5. Check of level of working liquid in system
5.2.6. Replacement of working liquid in system
5.2.7. Air removal from system
5.2.8. Test of the hydropump of system for developed pressure
5.2.9. Check of the sensor switch of pressure of the hydraulic booster of a steering
5.2.10. Check of a protective cover of the spherical hinge of a tip of steering draft
5.2.11. Check of the power absorbing mechanism of a steering column assembled
5.2.12. Removal and installation of a steering wheel
5.2.13. Removal and installation of a shaft of a steering column
5.2.14. Removal and installation of the hydropump of the amplifier of a steering
6. Brake system
7. Onboard electric equipment
8. Body
9. Appendix
10. Electric equipment schemes
 







5-2-11-proverka-ehnergopogloshhayushhego-mekhanizma-rulevojj-kolonki-v-sbore.html

5.2.11. Check of the power absorbing mechanism of a steering column assembled

In case of a road accident accompanied by strong front blow, force of blow is absorbed by the mechanism which has been built in a column of a steering wheel. Having once worked, this mechanism loses the ability to work repeatedly even if on it there are no visible damages after blow. To estimate operability of the power absorbing mechanism, it is necessary to execute the procedure of check stated below. If the mechanism already worked, it is necessary to replace a steering column assembled.
In the presence of a considerable free wheeling of a steering wheel at position of the lever of an inclination of a steering column in the locked situation, it is necessary to check a condition of a shaft of a steering column assembled.

ATTENTION
If the car continues movement after operation of the power absorbing mechanism, the shaft the helmsman of a column can be damaged in the course of continuation of operation of the car.
If the disposable capsule sagged, do not try to repair knot, simply replace a shaft of a steering column assembled.

Check technique
Remove the bottom and top guards of a steering column.

ATTENTION
Do not weaken the lever of an inclination of a steering column procedure of its installation and check of its condition is not finished yet.

Be convinced of that the lever of change of an inclination the helmsman of a column is blocked.

NOTE
If is not present, establish the lever of an inclination of a steering column in the blocked situation.

Check of the power absorbing mechanism of a steering column assembled
Weaken on two turns two top assembly bolts of fastening of a steering column.
Holding disposable capsules how it is shown in drawing, try to fix them. If the proslablen-nost of any of capsules is felt, необходио to replace a steering column assembled.

NOTE
At installation of a new shaft of a steering column assembled, establish the inclination lever in the blocked situation if it still is not in it.

ATTENTION
Be attentive, that to jam nothing between disposable capsules and a body.
Do not weaken the lever of an inclination of a steering column procedure of its installation and check of its condition is not finished yet.

If during check of any defects it is not revealed, tighten the nominal moment assembly bolts of fastening of a steering column.
Nominal moment of an inhaling: 12±2Н · m.


5.2.10. Check of a protective cover of the spherical hinge of a tip of steering draft

5.2.12. Removal and installation of a steering wheel