Repair and Mitsubishi Outlander service since 2003 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. General information
8.2. Hinged and decorative elements of a body
8.2.1. Removal and installation of a front bumper
8.2.2. Dismantling and assembly of a front bumper
8.2.3. Removal and installation of a rear bumper
8.2.4. Removal and front grille installation
8.2.5. Removal and installation of overlays of wings
8.2.6. Removal and installation of moldings
8.2.7. Removal and installation of a molding of a threshold
8.2.8. Removal and installation of a protective film of a frame of glass of a lateral door
8.2.9. Removal and installation of a back spoiler
8.2.10. Removal and installation of support of a luggage carrier of a roof
8.2.11. Cowl adjustment
8.2.12. Adjustment of the hatch of a jellied mouth of a fuel tank
8.2.13. Adjustment of forward and back lateral doors
8.2.14. Adjustment of glass of a lateral door
8.2.15. Check of a course of the external handle of a lateral door
8.2.16. Current check in a chain of the electric drive of a window regulator
8.2.17. Removal and cowl installation
8.2.18. Removal and installation of a lateral door assembled
8.2.19. Removal and installation of the lock and handle of a lateral door
8.2.20. Removal and installation of a back door assembled
8.2.21. Removal and installation of the lock and handle of a back door
8.2.22. Removal and installation of the hatch of a roof
8.2.23. Removal and installation of a lateral rear-view mirror
9. Appendix
10. Electric equipment schemes
 







8-2-13-regulirovka-perednejj-i-zadnejj-bokovykh-dverejj.html

8.2.13. Adjustment of forward and back lateral doors

Adjustment of forward and back lateral doors
If a gap on perimeter between a lateral door and a body non-uniform, paste a protective tape on a body round a loop and on the door region, then by means of the special tool weaken bolts of fastening of a loop of a door to a body. Moving a door, adjust a gap between a door and a body so that the gap was identical on all perimeter of a door.
Adjustment of forward and back lateral doors
If the closed door is not flush with a body surface, by means of the special tool weaken bolts of fastening of loops on a door and adjust the provision of a door so that its surface was aflush with a body surface.

ATTENTION
Do not make effort over 98 N the special tool.

NOTE
If washers of bolts of fastening of a loop of a door are welded, remove a door loop, then by means of a chisel or the detachable machine remove washer welding.
Establish a door loop into place, previously having painted over the damaged area of a loop paint from a repair kit or having processed anticorrosive structure.

Adjustment of forward and back lateral doors
If opening and door closing is complicated, adjust gearing of the lock and a door clamp by installation of additional laying between a clamp and a rack of a body and moving of a clamp either up-down, or to the right-to the left.

Adjustment of a back door
Adjustment of forward and back lateral doors
If opening and door closing is complicated, replace a clamp of the lock of a door and bolts of fastening of a clamp.
Temporarily tighten fastening bolts, then adjust gearing of the lock and a clamp of the lock of a door moving of a clamp of the lock either forward-back, or to the right-to the left.
Adjustment of forward and back lateral doors
After adjustment tighten bolts the nominal moment.
Inhaling moment: 20–28 N · m.

NOTE
If heads of bolts are hooked for edge of facing of a threshold of a back door, by means of a round file process places of contact of facing with a bolt.

Adjustment of forward and back lateral doors
If a gap on perimeter between a back door and a body non-uniform, weaken bolts of fastening of loops of a door and adjust a gap, moving loops.
Adjustment of forward and back lateral doors
Adjustment of forward and back lateral doors
Adjust height of an arrangement of a back door, turning rubber support of a door. At each complete turn of a rubber support the height increases approximately by 3 mm.


8.2.12. Adjustment of the hatch of a jellied mouth of a fuel tank

8.2.14. Adjustment of glass of a lateral door