Repair and Mitsubishi Outlander service since 2003 of release.
1. Operation and car maintenance
2. Engine
3. Transmission
4. Running gear
5. Steering mechanism
6. Brake system
7. Onboard electric equipment
8. Body
8.1. General information
8.2. Hinged and decorative elements of a body
8.2.1. Removal and installation of a front bumper
8.2.2. Dismantling and assembly of a front bumper
8.2.3. Removal and installation of a rear bumper
8.2.4. Removal and front grille installation
8.2.5. Removal and installation of overlays of wings
8.2.6. Removal and installation of moldings
8.2.7. Removal and installation of a molding of a threshold
8.2.8. Removal and installation of a protective film of a frame of glass of a lateral door
8.2.9. Removal and installation of a back spoiler
8.2.10. Removal and installation of support of a luggage carrier of a roof
8.2.11. Cowl adjustment
8.2.12. Adjustment of the hatch of a jellied mouth of a fuel tank
8.2.13. Adjustment of forward and back lateral doors
8.2.14. Adjustment of glass of a lateral door
8.2.15. Check of a course of the external handle of a lateral door
8.2.16. Current check in a chain of the electric drive of a window regulator
8.2.17. Removal and cowl installation
8.2.18. Removal and installation of a lateral door assembled
8.2.19. Removal and installation of the lock and handle of a lateral door
8.2.20. Removal and installation of a back door assembled
8.2.21. Removal and installation of the lock and handle of a back door
8.2.22. Removal and installation of the hatch of a roof
8.2.23. Removal and installation of a lateral rear-view mirror
9. Appendix
10. Electric equipment schemes
 







8-2-8-snyatie-i-ustanovka-zashhitnojj-plenki-ramki-stekla-bokovojj-dveri.html

8.2.8. Removal and installation of a protective film of a frame of glass of a lateral door

Removal
Removal and installation of a protective film of a frame of glass of a lateral door
Remove door facing assembled.
Remove an external sealant of a doorway.
Remove an internal sealant of a window of a door.
Remove directing fillet of glass of a door.
Remove a molding of a window of a door.
Removal of details is made in an order specified in drawing.

ATTENTION
In order to avoid burns be careful, do not touch a warm frame of glass of a lateral door and a protective film.

By means of the hair dryer heat up a protective film.
Finger hook edge of a protective film and then remove it completely.

Installation
Removal and installation of a protective film of a frame of glass of a lateral door
Removal and installation of a protective film of a frame of glass of a lateral door
Installation of details is made as it should be, the return to removal.
Be convinced that ambient temperature is in limits of 20-30 °C and a surface in a place of fastening of a protective film the pure.
If ambient temperature less than 15 °C, heat up protective films and a surface of its installation to 20–30 °C. If ambient temperature more than 35 °C, cool a protective film and a surface of its installation.
When drawing a protective film on a frame of glass of a lateral door be convinced that the edge of a protective film does not leave for frame edge.
When drawing a protective film use the special tool to avoid formation of folds and air vials.
Dry piece of a fabric (synthetic fiber) wipe the special tool and a protective film.
Clear (degrease) isopropyl alcohol of an installation site of a protective film.
Clear a film of pollution.
Put a protective film on a frame of glass of a lateral door.
Connect edges of a protective film with top and bottom edges of a frame of glass of a lateral door.

NOTE
Circles in drawings showed the places demanding special attention at installation.


8.2.7. Removal and installation of a molding of a threshold

8.2.9. Removal and installation of a back spoiler